NCR New Concept RDA
NCR New Concept RDA brings innovation to rebuildable tanks! It features coil-free design for no wire building. Just clamp the cotton and enjoy the flavor!
- 100% гарантия качества
- 24-часовая отправка
- Гарантия возврата денег за 7 дней
Вы можете смешать следующие предметы, чтобы получить оптовую скидку.
USD 999.00 USD 999.00
USD 58.90 USD 88.35
USD 29.99 USD 45.00
USD 5.58 USD 8.37
USD 30.99 USD 46.49
USD 31.99 USD 48.00
USD 38.49 USD 58.00
USD 27.50 USD 39.00
USD 26.00 USD 39.00
USD 22.80 USD 33.00
Note: You can check the Safe Report about ALUMINUM NITRIDE (the material of NCR WAFER heater) here.
Are you tired of the wires, coils and time-consuming building? Then the NCR New Concept RDA is right here for you! It features a food-grade PC outer cover with venting holes, providing a safe vaping experience. The 600,000 times cycle-uses a WAFER heater that holds up the resistance of 0.4-0.5ohm and is capable of self-cleaning within a short-time dry burning in 30-40W. This pack also comes with a heat-isolation gasket. Available in White.
Size: 24(D) x 40mm (H) (with 510 thread)
WAFER Material: SST aluminum nitride
WAFER Heater Resistance: 0.4-0.5ohm
Thread: 510 thread
Coil-free Design, No Wire Building
600,000 Times Cycle-use WAFER Heater(0.4-0.5ohm resistance)
Visible Outer Cover with Venting Holes
Strengthened Nicotine Effect
It comes with
- 1x NCR New Concept RDA
- 1x Tool Pack
Simple packing. Customary Packing from the factory, the packing is subject to change without notice.
Installation and preparations: Put the Wafer Heater into the deck slot and screw it with the Allen wrench. Check the resistance by connecting it with a MOD.(Wafer heater is usually pre-installed ex-work. Due to the different feature of various mods, resistance may range from 0.4-0.5ohm accordingly.)
How to fold the cottons: Pre-cut Organic cotton is strongly recommended. Cut each piece of cotton into a strip with the size of 8mm(width)* 40mm(length). Fold the cotton strips from middle and cover the wafer heater from the top and insert the cotton ends into the deck.
How to fix the cotton holder: Put on the aluminum cotton holder to fix the cotton strips. Make sure the cotton strips are fixed properly for E-juice soaking and vaporization. Moisten the new cotton with E-juice from all the openings on the top, bottom and all 4 sides of the cotton holder.
Output modes selection: The MOD with AOC Power mode（Adjustable Output Curve）or Boosting mode is strongly recommended. To optimize the wafer heating function, please set up a considerably high wattage（70W-80W）at the initial firing stage for around 0.5-1 second, then drop the wattage to a relatively low level(40W-50W) to last for another 2-3 seconds. Users may customize the Power mode settings to personal preference.
Clean the dirt and stains on the Wafer Heater: After being used for some time, you need to clean the Wafer Heater. Remove the cotton holder and give the Wafer Heater a dry burn at 30W-40W in 3 seconds. A fine grade sand paper can also be used to rubbed off the stubborn stains on the Wafer Heater. For regular maintenance you may use a toothbrush to clean the RDA deck and all connections with household detergents.
- The material of WAFER is safe. Please check the official announcement from NCR.
- 510 thread.
- You can select the e-juice/replacement wafer heater.
- You can select cotton for easy building.
- Don't use the NCR with mechanical MODs.
Share your thoughts with other customersНаписать обзор
Typical questions asked about products:
- Is the item durable?
- Is this item easy to use?
- What are the dimensions of this item?